為了延長潛水泵的使用壽命，專用保護器必不可少，像現在設成上常見的漏水保護器，過熱保護器材等。除了必不可少的保護器，我人在使用中還需要注意以下幾個問題
一、正確的電機旋轉方向 正確安排潛水泵，確保電機旋轉方向正確。現在許多的潛水電泵正轉反轉都可以出水，但反轉時出水量小，電流大，時間工了會損壞電機。
二、確保電壓正常再開機 由于低壓供電線路較長，線路末端電壓過低是常見的。當電壓過低時，潛水泵電機轉速下降，當達不到轉速的70%時，啟動離心開關會閉合，造成啟動繞組長時間通電而發熱，甚至燒壞電容。而電壓過高引起電機過熱而燒壞繞組。所以當電源電壓低于額(e)定電壓10%或高于額(e)定電壓10%時，應停止電機運轉，找出原因并排除故障
三、電纜線安裝與潛水電泵的絕緣電阻要求 安裝潛水泵時，電纜線要架空電源線不要太長，潛水泵下水或提出時切勿使電纜受力，以免引起電源線斷裂。潛水泵工作時不要沉入泥中，否則會導致電機散熱不良而燒壞電機繞組，安裝時，絕緣電阻不應代于0.5M
四、漏電保護器的安裝 因為潛水泵在水下工作，容易漏電造成電能損失甚至引發觸電事故。漏電保護器會在潛水泵漏電值超過漏電保護器的動作電流值時，切斷電源，確定安全。
五、避免頻繁開頭 不要頻繁地開關潛水泵，這是因為電泵停轉時會產生回流，若立即開機，會使電機負載啟動，導致啟動電流過大而燒壞繞組。
六、避免潛水電泵長期超負荷工作 不要抽含沙量大的水并隨時觀察電流值是否在銘牌的的規定數值，若發現電流過大，應停機檢查。
七、注意日常維護 平時要經常檢查電機，如發現下蓋有裂紋、橡膠密封損壞或失效等，應及時更換或修復，避免水滲入潛水泵。 如果您在日常使用中有任何疑問，也歡迎您隨時與我們聯系，泵一將竭誠為您服務!